Open Access

To increase productivity when joining galvanised sheet metal, metal inert gas (MIG) and tungsten inert gas (TIG) arc brazing are combined in a hybrid process. This coupling of two arc processes increases brazing speed and reduces weld reinforcement and the tendency to spatter. Because the arcs are 6 mm apart, they influence each other. Therefore, the blowing action is a major challenge in hybrid arc brazing. A current modulation and the optimal relative position of the arcs to each other are compulsory conditions. Selected brazing parameters are tested in order to verify the hybrid arc brazing. Overlap joints are brazed on galvanised sheets. The mechanical-technological properties of the brazed joints are determined. It has been shown that hybrid brazing can achieve significantly higher brazing speed with the same or better brazing quality compared to standard arc brazing. For the realisation of the hybrid arc brazing process, software-controlled welding machines are used, which will replace conventional power sources in the future.

For use in micromechanical simulations of continuous fiber reinforced polymers, a more general form of the paraboloid failure criterion by Stassi‐D'Alia for matrix failure was developed with explicit consideration of the hydrostatic tension strength. Regarding polymers, limits for hydrostatic tensile strength based on isotropic linear elasticity could be derived. The comparison of the newly developed extended paraboloid criterion with experimental data for yielding as well as for material separation (fracture) shows good agreement.

In this work, a new method for selecting suitable materials is presented. This method has a high potential for a variety of engineering applications, such as the design of sound-absorbing and vibration-loaded structures, where a large number of different requirements have to be met. The method is based on the derivation of functional dependencies of selected material parameters. These dependencies can be used in parameter studies to consider parameter combinations that lie in the range of real existing and targeted material groups. This allows the parameter space to be reduced, the calculation to be accelerated, and suitable materials to be (pre-)selected for the respective application, which contributes to a more target-oriented design. The method is applied to the example of a plate resonator. For this purpose, a semi-analytical model is implemented to calculate the transmission loss as well as the reflected and dissipated sound power of plate silencers, taking into account the influence of flow velocity and fluid temperature on the performance of plate silencers.

The atomizing gas dynamics and the applied process energy have a significant influence on the produced particles. The melting process of the two wires can be influenced by current modulation. As for arc welding processes, more and more electronic and software-controlled machines are being used for arc spraying and will have replaced conventional power sources in the future. Due to the highly dynamic, fast regulating computing technology in the latest energy source, technology arcs can be operated with different current forms and types. The modern machines allow process-stable, reproducible variation of the particles and heat input into the substrate. Constant and pulsed current can be used as current forms. Usable current types are direct current (DC) and alternating current (AC). The electrical parameters must be analyzed to evaluate the process behavior. The consumable used is a wire-shaped iron-based alloy with a diameter of 1.6 mm. Relevant process parameters such as basic current Iground, pulse current Ipulse, pulse duration tpulse, impulse frequency fpulse, and alternating current frequency, fAC, are varied and recorded using appropriate measurement technology. The aim is to change the process performance and thereby the particle formation in a broad band. High-speed images are used to observe the arc and the deposition process. In addition, particle sizes are determined.

Introduction: In the spring of 2020, coronavirus disease 2019 posed a substantial challenge for countries and their healthcare systems. In Germany, over 70% of all cancer patients are treated in an outpatient setting, so gynecologic oncology practices are the guarantors of optimal patient care. We developed a survey to evaluate the management of gynecologic oncology patients. Methods: The survey consisted of 38 questions and was sent to the members of the Berufsverband Niedergelassener Gynäkologischer Onkologen in Deutschland e.V. (BNGO), a professional association of gynecologic oncologists in the outpatient sector in Germany. Results: The survey was completed by 54 out of 133 (41%) gynecologic oncologists from 14 out of 15 (93%) federal states where the BNGO is represented. Facing the pandemic, popular measures were mask requirements (100%), restriction of access to practices (94%), increased number of disinfectant dispensers (85%), installment of panes of acrylic glass (76%), or spatial alterations (67%). For most patients the pandemic had no influence on prioritization of therapies (82%) or prescribed systemic treatments (87%). Despite an increase in perceived psychological burden among the staff (72%), 85% (45/54) of the practices were not offered any additional psychological support. Discussion and Conclusion: As most cancer patients in Germany are treated in an outpatient setting, a suitable reaction of oncology centers to the new circumstances was crucial to secure optimal treatment and patient care. Nevertheless, the low prioritization of mental health or distress of healthcare workers poses a serious threat to the maintenance of optimal medical care in further waves of the pandemic.