OPUS documents https://libdoc.whz.de/opus4/index/index/ Wed, 26 Mar 2025 14:02:35 +0100 Wed, 26 Mar 2025 14:02:35 +0100 https://libdoc.whz.de/opus4/frontdoor/index/index/docId/18231 Sebastian Weis; Stefan Brumm; Robin Grunert; Manuel Halmaghi; Jan Morgenschweis; Jürgen Bosler article https://libdoc.whz.de/opus4/frontdoor/index/index/docId/18231 Wed, 26 Mar 2025 14:02:35 +0100 https://libdoc.whz.de/opus4/frontdoor/index/index/docId/17954 Ni-based brazing fillers are primarily utilized in vacuum furnaces or continuous furnaces. However, the application of such furnace techniques imposes technical and economic limitations on the size of brazeable components. Induction brazing offers an alternative to overcome these limitations, enabling the brazing of large components by means of localized heating and gas shielding. This study aims to improve the understanding of process control and required gas quality for effective brazing by conducting experiments on tube-to-tube joints using Ni-based brazing alloys. To determine their impact on brazing outcomes, process gases with varying oxygen contents were systematically tested. The microstructure of the brazed joints was analyzed by light microscopy. The influence of process gas quality on corrosion behavior was examined using a capillary microcell. High residual oxygen contents in the process gas led to a shift in the corrosion potentials. Additionally, the mechanical properties of the joints are affected. Therefore, the monotonic mechanical properties were investigated at ambient temperature. The findings of this research offer practical recommendations and present a newly developed shielding gas nozzle for industrial applications. These insights support the optimization of induction brazing processes and highlight the potential for increasing the quality and efficiency of brazing large components. Sebastian Weis; Robin Grunert; Vasilii Fedorov; Stefan Brumm; Thomas Uhlig article https://libdoc.whz.de/opus4/frontdoor/index/index/docId/17954 Mon, 09 Dec 2024 06:33:26 +0100 https://libdoc.whz.de/opus4/frontdoor/index/index/docId/17487 Sebastian Weis; Stefan Brumm; Robin Grunert; Manuel Halmaghi; Jan Morgenschweis; Jürgen Bosler article https://libdoc.whz.de/opus4/frontdoor/index/index/docId/17487 Mon, 29 Jul 2024 08:48:23 +0200 https://libdoc.whz.de/opus4/frontdoor/index/index/docId/16876 Duplex steels are used for applications that require high strength and ductility combined with good corrosion resistance. An economical welding technology to handle these steels is achieved by combining the MIG and TIG arc processes. The aim is to improve welding speed and quality by utilizing a TIG-MIG hybrid welding process to join 1.4462 duplex steel with a thickness of 2 mm. The interaction between the two arcs, caused by the blowing effect, is an enormous challenge that can be counteracted with a defined torch position and current modulation. For this purpose, a variation of the MIG (pulsed and AC pulsed arc) and TIG process (AC and pulsed DC) took place. The influence of electrical parameters on process stability and material transfer was investigated. For analysis, an evaluation of high-speed recordings (5000 frames per second) and synchronized measured current/voltage curves (200 kHz) is carried out. Based on a number of selected specimens, a welding procedure test according to ISO 15614-1 is performed to determine the welding seam quality. The test includes the characterization by tensile and hardness testing and macroscopic and microscopic examination. Additionally, the specimens are examined according to ISO 5817. Sebastian Weis; Robin Grunert; Stefan Brumm; Manuel Halmaghi; Ulrich Prank article https://libdoc.whz.de/opus4/frontdoor/index/index/docId/16876 Fri, 15 Mar 2024 09:58:27 +0100 https://libdoc.whz.de/opus4/frontdoor/index/index/docId/16403 To increase productivity when joining galvanised sheet metal, metal inert gas (MIG) and tungsten inert gas (TIG) arc brazing are combined in a hybrid process. This coupling of two arc processes increases brazing speed and reduces weld reinforcement and the tendency to spatter. Because the arcs are 6 mm apart, they influence each other. Therefore, the blowing action is a major challenge in hybrid arc brazing. A current modulation and the optimal relative position of the arcs to each other are compulsory conditions. Selected brazing parameters are tested in order to verify the hybrid arc brazing. Overlap joints are brazed on galvanised sheets. The mechanical-technological properties of the brazed joints are determined. It has been shown that hybrid brazing can achieve significantly higher brazing speed with the same or better brazing quality compared to standard arc brazing. For the realisation of the hybrid arc brazing process, software-controlled welding machines are used, which will replace conventional power sources in the future. Sebastian Weis; Robin Grunert; Stefan Brumm; Ulrich Prank article https://libdoc.whz.de/opus4/frontdoor/index/index/docId/16403 Mon, 04 Mar 2024 07:56:47 +0100 https://libdoc.whz.de/opus4/frontdoor/index/index/docId/16568 The atomizing gas dynamics and the applied process energy have a significant influence on the produced particles. The melting process of the two wires can be influenced by current modulation. As for arc welding processes, more and more electronic and software-controlled machines are being used for arc spraying and will have replaced conventional power sources in the future. Due to the highly dynamic, fast regulating computing technology in the latest energy source, technology arcs can be operated with different current forms and types. The modern machines allow process-stable, reproducible variation of the particles and heat input into the substrate. Constant and pulsed current can be used as current forms. Usable current types are direct current (DC) and alternating current (AC). The electrical parameters must be analyzed to evaluate the process behavior. The consumable used is a wire-shaped iron-based alloy with a diameter of 1.6 mm. Relevant process parameters such as basic current Iground, pulse current Ipulse, pulse duration tpulse, impulse frequency fpulse, and alternating current frequency, fAC, are varied and recorded using appropriate measurement technology. The aim is to change the process performance and thereby the particle formation in a broad band. High-speed images are used to observe the arc and the deposition process. In addition, particle sizes are determined. Sebastian Weis; Stefan Brumm; Robin Grunert; Jan Morgenschweis; Jürgen Bosler; Thomas Grund article https://libdoc.whz.de/opus4/frontdoor/index/index/docId/16568 Fri, 01 Mar 2024 07:25:21 +0100